Showing all 6 results
3/4 Channel Amps
Audison Prima AP4 D
.Add this 4-channel Prima amplifier to a 4.9 bit or 5.9 but amplifier. When integrating with factory fitted multi-speaker systems this add on is a must for expanding the capabilities of Prim bit amplifiers. Sharing the same footprint, up to three Prima amplifiers can be stacked for maximum space efficiency without over heating.
Load Imp. 4 Channels 2 Channels (bridge) 4 Ohm 70 W x 4 260 W x 2 2 Ohm 130 W x 4(0 reviews)£349.99 Add to basket
Audison Prima AP1 D
The Prima AP1 D amplifier was designed to drive a subwoofer and is the ideal extension of the AP8.9 bit and AP4.9 bit. At 2 Ohms it is stable and can supply 540 W power with extremely compact dimension. With the APTK 3 (Audison Prima Tower Kit 3) staking system it’s possible to stack the AP1 D and save space without any problem of overheating.
Load. Imp. Mono 4 Ohm 310 W 2 Ohm 540 W(0 reviews)£349.99 Add to basket
3/4 Channel Amps
Audison Prima AP4.9 bit
The Bit DSP equipped 4-channel Prima amplifier offers huge integration possibilities while the powerful on-board processor adds a new dimension in sound customisation. Designed to overcome the problems inherent in car design and the low priority always given to sound reproduction Prima will enthuse, excite and engage. A 9-channel DSP offers fantastic upgrade options. Add an AP4 D and AP1 D for an additional four channels and dedicated subwoofer output.(0 reviews)£599.99 Add to basket
5/6 Channel Amps
Audison Prima AP5.9 bit
AP5.9 bit amplifier is ideal to realize a two way front full active plus subwoofer system using the fifth mono channel with 270 W @ 2 Ω. The built-in processor, that this amplifier shares with the AP8.9 bit, provides the ability to assign the pre-outs to the AP4 D amplifier, creating a very powerful system in a small space thanks to the “rack mounting” system.
Load. Imp. 5 Channels 4 Ohm 20 W x 2 + 50 W x 2 + 150 W x 1 2 Ohm 40 W x 2 + 90 W x 2 + 270 W x 1
Accessories [NOT INCLUDED]
DRC – Digital Remote Control
The DRC is the digital interface between the AP5.9 bit and the user. The DRC mounted in the vehicle dashboard, provides access to control of the inputs and volume adjustments, balance, fader and subwoofer volume. Providing source selection between main, aux and optical inputs, it also provides four of the configurations created and saved by the bit one right at hand. The DRC also controls the functions of the Audison Thesis amplifiers when these are installed in the same system.
DRC Cable Extension kit for installations on especially long vehicles. Total length of the supplied cable with the extension is equal to 6,5 m / 225,90″.
OP 1.5 • TOSLINK Optical Cable
Optical cable ending with TOSLINK connectors for S/PDIF digital audio signals. Cable length: 1,5 m / 59,05″.
OP 4.5 • TOSLINK Optical Cable
Optical cable ending with TOSLINK connectors for S/PDIF digital audio signals. Cable length: 4,5 m/177,16″
STA • F/F Socket TOSLINK adapter
Optical adapter to extend optical cables featuring TOSLINK connectors.
APL 2 – (AP4 D / AP1 D) link cable
Cable to connect AP5.9 bit to AP4 D and AP1 D amplifiers.
AP T-Harness “DCC”.
T-Harness “DCC” is the Plug&Play solution to integrate Audison Prima with the
factory car audio system.
AP Extension cables.
The Extension cable with Plug&Play connections allows total freedom in positioning the AP bit amplifiers.
AP Speakers Output cables.
The AP Speakers Output for AP5.9 bit is dedicated to the connection of the AP bit amplifiers with the input/output Extension cable.
SPM4 – 4 Ch Stereo Passive Mixer
Recommended to extend the number of inputs of AP bit amplifiers because they feature a De-equalizer (De-Eq). In that case, any possible non-linear acoustic emissions due to the mixing of the pre-existing filtered channels are duly compensated.
(0 reviews)£649.99 Add to basket
7/8 Channel Amps
Audison Prima AP8.9 bit
Audison Prima AP8.9 bit
This extremely versatile plug and play amplifier will set your speakers free from the constraints of vehicle manufacturers sound curves. 8-channels and Bit technology in a very compact case.
Following a lengthy and comprehensive development programme, the Audison AP8.9 Bit amplifier offers fabulous sound enhancement for multi-speaker amplified factory car audio systems. Research revealed that many car speakers are not driven with enough power to offer the control required for a car speaker system. Furthermore, distortion rapidly increases to unpleasant levels when the volume is turned up. The clean signal handling of the eight class D channels and the incredible signal processing power overcomes many of the stock issues.
Technical SpecificationDistortion – THD (1kHz @ 4Ohms, 90% Power): 0.05 %
Bandwidth (-3 dB, 2 V RMS, 4Ohms): 10Hz – 22KHz
S/N ratio @ A weighted, 1V, Max Power: 95 dBA
Damping factor @ 1 kHz, 2 V RMS, 4Ohms): >70
Input sensitivity: 2 – 15 V RMS
Input impedance: 15KOhms
LOAD IMPEDANCE (MIN):
• 8 Ch: 2Ohms
• 4 Ch – Bridge (1-2) (3-4) (5-6) (7-8): 4Ohms
OUTPUT POWER (RMS) @ 12.0 – 14.4 VDC, 1% THD:
• 8 Ch @ 4Ohms: 35 W x 8
• 8 Ch @ 2Ohms: 65 W x 8
• 4 Ch – (Bridge 1/2; 3/4; 5/6; 7/8) @ 4Ohms: 130 W x 4
OUTPUT POWER (RMS) @ 14.4 VDC, 10% THD:
• 8 Ch @ 4Ohms: 45 W x 8
• 8 Ch @ 2Ohms: 85 W x 8
• 4 Ch – (Bridge 1/2; 3/4; 5/6; 7/8) @ 4Ohms: 170 W x 4DIGITAL SIGNAL PROCESSOR
(32 bit Cirrus Logic; Clock speed: 147 MHz)
Crossover: Full / Hi Pass / Lo Pass / Band Pass
Crossover type and slope:
Linkwitz @ 12/24 dB – Butterworth @ 6/12/18/24 dB
Crossover Frequency: 68 steps @ 20Hz – 20KHz
Phase inversion: 0° / 180°
Analog Input Equalizer: Automatic De-Equalization
N.9 Parametric Equalizers: ±12 dB;10 pole; 20Hz – 20KHz
Time Alignment Distance 0 – 510 cm / 0 – 200.8 in.
Time Alignment Delay 0 – 15 ms
Time Alignment Step 0.08 ms; 2.8 cm / 1.1 in.
Time Alignment Fine Set 0.02 ms; 0.7 cm / 0.27 in.
Preset (Drive Preset) Rotary switch for 7 installation Presets
Acoustic Preset N.2 DSP Memory, DRC selectable(0 reviews)£749.99 Add to basket
Audison Prima AP F8.9 bit
Audison Prima amps incorporating bit processor have been around for a while now. Conceived as the ultimate integration product, they have by necessity featured relatively low power, to optimise plug and play opportunities without the need to provide a high current supply from the vehicle battery. This new “F” version more than doubles the power rating delivering a very creditable 85 Watts per channel. The amplifier can be configured to run in bridged mode and will also operate quite happily when driving a 2-ohm load offering potential power output of up to 260 watts for a pair of bridged channels.
Fully loaded with the renowned bit DSP engine, this is an amplifier for all seasons!(0 reviews)£999.99 Add to basket