
Audison VOCE AV 6.5
Originating directly from the experience of the Thesis line components, the Voce woofer features an aluminium basket with a great aerodynamic structure, a cotton-fibre paper pressed cone with Light Damping treatment, a Triple Wave surround in butyl rubber and extremely light Copper Clad Aluminium Wire coils.
Technical Data
Comp | Woofer |
Size | 165 mm (6″) |
Power Handling | 100 W Continuous Power 200 W Peak Power |
Impedance | 4 Ω |
Frequency Response | 50 ÷ 7k Hz |
Sensitivity | 91 dB/Spl |
Magnet | High density flux ferrite |
Dome | Cotton-Fibre pressed paper with Light Damping treatment |
£199.99
Out of stock
Additional information
Dimensions | 60 × 60 × 60 cm |
---|
Related products
- CAR AUDIO
Audison APBMW S8-4
*£229.99 each
APBMW S8-4
SUBWOOFER FOR BMW-MINI
Subwoofers have been designed with electro-acoustic parameters that maximize performance for the factory box available below the seats. The ABS plastic basket, reinforced with fibreglass, and the acoustic structure featuring a front magnet, provide for a minimal installation depth for a perfect compatibility with the whole range. Two 5 mm polyurethane gaskets, supplied, allowing the subwoofer to fit perfectly into the box, decoupling it from vibration.
The 200 mm (8″) APBMW S subwoofers allow a “direct replacement” of the OEM speakers underneath the front seats, making the most of the factory acoustic load and generating deep and crisp low frequencies. You can choose between S8-2 with 2-ohm impedance and S8-4 with 4-ohm impedance for improved system composition versatility. In fact, in the mid-high passive filtered system configuration, with the crossover provided, 4 of the 8-channels of the AP 8.9 bit can be configured in bridge mode delivering 130W RMS to each S8-4 installed under the seat. The S8-2 can be used in a fully active, multi-amplified front system, maximizing the power of the AP 8.9 bit at 2 ohms, and employing additional 2 channels for the rear system. The Neodymium magnet used on S8-4 and S8-2 allows for greater power and control than ferrite while maintaining the depth of installation unaltered.
Rated 0 out of 5(0 reviews)£239.99 Add to basket - CAR AUDIO
Audison Prima AP 6.5
The Audison Prima AP6.5 – 6.5inch woofer -designed for upgrade & replacement with Oem type woofers that are generally fitted in vehicles that have a active system.
The Audison AP 6.5 feature a 32 mm pure copper voice coil, for high power handling and outstanding low frequency control. All the woofer don’t employ any filter, to maximize efficiency: the dome profile has been optimised with Klippel R&D Scan Vibrometer to obtain a calibrated mechanical low-pass cut-off frequency. The surround features the exclusive shallow “Triple Wave” profile, for maximum excursion linearity.
Featuring a 32 mm pure copper mobile voice coil, for high power handling and outstanding low frequency control this Prima 6.5″ has a treated water-repellent paper cone, featuring a profile developed with FEM (Finite Element Method) simulation technology and optimised using Klippel R&D Scan Vibrometer technology.
Tecnical Data
Comp Woofer Size 165 mm (6,5″) Power Handling 70 W Continuous Power
210 W Peak PowerImpedance 4 Ω Frequency Response 60 ÷ 5k Hz Sensitivity 93,5 dB/Spl Magnet High density flux ferrite Dome Water-repellent treated paper cone Rated 0 out of 5(0 reviews)£84.99 Add to basket - CAR AUDIO
Audison Prima APBX 8R
This neat little subwoofer and enclosure combo is reflex loaded and tuned to develop high level at low frequencies. Exploiting the natural boost in output found in most cars below 60 Hz known as “cabin gain”, the 8-inch single 4 Ω voice-coil subwoofer has a powerful motor that maximises efficiency. This makes the APBX 8 R the perfect companion to the Audison Prima AP8.9 bit amplifier. The low-resonant frequency of the subwoofer, matched to the reflex enclosure keeps excursion to a minimum within the entire audio spectrum offering exceptional output from a modest amplifier such as bridged channels of an Audison Prima AP4.9 bit / AP4 D delivering 260 W rms.
Technical Specification
LOADED REFLEX SUB BOX
Size: 200 mm (8”)
Power Handling: 250 W Continuous Power 500 W Peak Power
Impedance (Ohms): 4
Sub box size mm (in.): 473 (18.62) x 334 (13.15) x 109 (4.29)
Magnet: High density flux ferrite
Cone: Cotton-Fibre pressed paper
Weight of one component kg (lb): 6.64 (14.64)Rated 0 out of 5(0 reviews)£309.99 Add to basket