Hertz Bass Baby
Hertz ES 200.5 Energy Subwoofer with custom made UK enclosure delivering lots of bass from the smallest of space. Finished with a stylish designer grill as you would expect.
Box Size – L 476mm x H 287mm x D 140mm
Total Weight with Woofer – 5.9Kg
Size – 200mm (8in.)
Power handling – 600W peak, 200W continuous
Impedance – 4Ohm
Frequency response – 30 – 400Hz
Sensitivity – 88.5dB/SPL
Magnet size – 120 x 60 x 34mm
Total Driver Replacement – 0.82L
Voice Coil – 50mm diameter
Magnet – High density flux ferrite
Cone – Water repellent pressed paper
Weight – 3.7kg
X-mech – +/- 13mm
- CAR AUDIO
Audison APBMW S8-4
SUBWOOFER FOR BMW-MINI
Subwoofers have been designed with electro-acoustic parameters that maximize performance for the factory box available below the seats. The ABS plastic basket, reinforced with fibreglass, and the acoustic structure featuring a front magnet, provide for a minimal installation depth for a perfect compatibility with the whole range. Two 5 mm polyurethane gaskets, supplied, allowing the subwoofer to fit perfectly into the box, decoupling it from vibration.
The 200 mm (8″) APBMW S subwoofers allow a “direct replacement” of the OEM speakers underneath the front seats, making the most of the factory acoustic load and generating deep and crisp low frequencies. You can choose between S8-2 with 2-ohm impedance and S8-4 with 4-ohm impedance for improved system composition versatility. In fact, in the mid-high passive filtered system configuration, with the crossover provided, 4 of the 8-channels of the AP 8.9 bit can be configured in bridge mode delivering 130W RMS to each S8-4 installed under the seat. The S8-2 can be used in a fully active, multi-amplified front system, maximizing the power of the AP 8.9 bit at 2 ohms, and employing additional 2 channels for the rear system. The Neodymium magnet used on S8-4 and S8-2 allows for greater power and control than ferrite while maintaining the depth of installation unaltered.Rated 0 out of 5(0 reviews)£239.99 Add to basket
- CAR AUDIO
Focal IC FORD 165 – Ford Coaxial Speaker Replacement
Also available in component – [Here]Rated 0 out of 5(0 reviews)
£159.95£129.95 Read more
- CAR AUDIO
Audison Prima AP5.9 bit
AP5.9 bit amplifier is ideal to realize a two way front full active plus subwoofer system using the fifth mono channel with 270 W @ 2 Ω. The built-in processor, that this amplifier shares with the AP8.9 bit, provides the ability to assign the pre-outs to the AP4 D amplifier, creating a very powerful system in a small space thanks to the “rack mounting” system.
Load. Imp. 5 Channels 4 Ohm 20 W x 2 + 50 W x 2 + 150 W x 1 2 Ohm 40 W x 2 + 90 W x 2 + 270 W x 1
Accessories [NOT INCLUDED]
DRC – Digital Remote Control
The DRC is the digital interface between the AP5.9 bit and the user. The DRC mounted in the vehicle dashboard, provides access to control of the inputs and volume adjustments, balance, fader and subwoofer volume. Providing source selection between main, aux and optical inputs, it also provides four of the configurations created and saved by the bit one right at hand. The DRC also controls the functions of the Audison Thesis amplifiers when these are installed in the same system.
DRC Cable Extension kit for installations on especially long vehicles. Total length of the supplied cable with the extension is equal to 6,5 m / 225,90″.
OP 1.5 • TOSLINK Optical Cable
Optical cable ending with TOSLINK connectors for S/PDIF digital audio signals. Cable length: 1,5 m / 59,05″.
OP 4.5 • TOSLINK Optical Cable
Optical cable ending with TOSLINK connectors for S/PDIF digital audio signals. Cable length: 4,5 m/177,16″
STA • F/F Socket TOSLINK adapter
Optical adapter to extend optical cables featuring TOSLINK connectors.
APL 2 – (AP4 D / AP1 D) link cable
Cable to connect AP5.9 bit to AP4 D and AP1 D amplifiers.
AP T-Harness “DCC”.
T-Harness “DCC” is the Plug&Play solution to integrate Audison Prima with the
factory car audio system.
AP Extension cables.
The Extension cable with Plug&Play connections allows total freedom in positioning the AP bit amplifiers.
AP Speakers Output cables.
The AP Speakers Output for AP5.9 bit is dedicated to the connection of the AP bit amplifiers with the input/output Extension cable.
SPM4 – 4 Ch Stereo Passive Mixer
Recommended to extend the number of inputs of AP bit amplifiers because they feature a De-equalizer (De-Eq). In that case, any possible non-linear acoustic emissions due to the mixing of the pre-existing filtered channels are duly compensated.Rated 0 out of 5(0 reviews)£649.99 Read more