Skinz Expert Bulk pack
The Expert Bulk pack-the best all round sound deadening for the pure Audiophile27 Sheets – 375mm x 265mm x 3mm (2.8sq.m – 30sqft)
Skinz sound deadening and panel lining products – For great car audio it all begins with properly treating your vehicle doors & panels . Flexing of the metal panels & rattles from plastic trims not only ruin a great sound system in a car but becomes a nuisance for the drivers entertainment . With the Skinz soundproofing material applied to your vehicle your can eliminate & cancel rattles & vibrations that would resonate through your vehicle. Great Skinz soundproofing goes as far as possible in eradicating noises with add-on options Skinz products like wave diffuser which will absorb the sound issuing from the rear of your speakers to prevent that sound reflecting back into the speakers. The importance of sound treatment such as the Skinz range should never be underestimated.
Great car sounds with great soundproofing!
Audison Prima AP5.9 bit
AP5.9 bit amplifier is ideal to realize a two way front full active plus subwoofer system using the fifth mono channel with 270 W @ 2 Ω. The built-in processor, that this amplifier shares with the AP8.9 bit, provides the ability to assign the pre-outs to the AP4 D amplifier, creating a very powerful system in a small space thanks to the “rack mounting” system.
Load. Imp. 5 Channels 4 Ohm 20 W x 2 + 50 W x 2 + 150 W x 1 2 Ohm 40 W x 2 + 90 W x 2 + 270 W x 1
Accessories [NOT INCLUDED]
DRC – Digital Remote Control
The DRC is the digital interface between the AP5.9 bit and the user. The DRC mounted in the vehicle dashboard, provides access to control of the inputs and volume adjustments, balance, fader and subwoofer volume. Providing source selection between main, aux and optical inputs, it also provides four of the configurations created and saved by the bit one right at hand. The DRC also controls the functions of the Audison Thesis amplifiers when these are installed in the same system.
DRC Cable Extension kit for installations on especially long vehicles. Total length of the supplied cable with the extension is equal to 6,5 m / 225,90″.
OP 1.5 • TOSLINK Optical Cable
Optical cable ending with TOSLINK connectors for S/PDIF digital audio signals. Cable length: 1,5 m / 59,05″.
OP 4.5 • TOSLINK Optical Cable
Optical cable ending with TOSLINK connectors for S/PDIF digital audio signals. Cable length: 4,5 m/177,16″
STA • F/F Socket TOSLINK adapter
Optical adapter to extend optical cables featuring TOSLINK connectors.
APL 2 – (AP4 D / AP1 D) link cable
Cable to connect AP5.9 bit to AP4 D and AP1 D amplifiers.
AP T-Harness “DCC”.
T-Harness “DCC” is the Plug&Play solution to integrate Audison Prima with the
factory car audio system.
AP Extension cables.
The Extension cable with Plug&Play connections allows total freedom in positioning the AP bit amplifiers.
AP Speakers Output cables.
The AP Speakers Output for AP5.9 bit is dedicated to the connection of the AP bit amplifiers with the input/output Extension cable.
SPM4 – 4 Ch Stereo Passive Mixer
Recommended to extend the number of inputs of AP bit amplifiers because they feature a De-equalizer (De-Eq). In that case, any possible non-linear acoustic emissions due to the mixing of the pre-existing filtered channels are duly compensated.
(0 reviews)£649.99 Add to basket
Audison Prima APS 8 R
This superb range of shallow subwoofers are designed and developed to overcome the short excursion limitations suffered by many competitor products which lead to underwhelming performance. Audison Prima subwoofers truly are the answer for those wanting maximum bass form minimum space.
Component: Single coil Subwoofer
Size: 200 mm (8”)
Power Handling: 250 W Continuous Power
500 W Peak Power
Impedance (Ohms): 4
Sensitivity: 84 dB/W/m
Magnet: High density flux ferrite
Cone: Cotton-Fibre pressed paper
Xmech: 16.5 mm (0.65″)(0 reviews)£169.99 Add to basket
Alpine X803D U Navigation System
8” Touch Screen Navigation with TomTom maps, compatible with Apple CarPlay and Android Auto – X803D-U
The X803D-U Advanced Navi Station brings the latest media compatibility, cutting-edge navigation technology and Alpine’s audiophile sound quality to your ride. It is fully compatible with the latest smartphones such as the iPhone 7 and the Galaxy S7 and lets you use Android Auto and Apple CarPlay on its 8-inch high-resolution touch screen.
DAB+ digital radio, USB video playback, HDMI connectivity and the latest Bluetooth technology are built-in as well.
You even have 3 options for navigation: the X803D-U features the iGo Primo NextGen navigation system with TomTom maps and 3 years free-of-charge map update. It also includes online navigation capability to use Maps with Apple CarPlay and Google navigation with Android Auto. Both Apple CarPlay and Android Auto apps can access the Alpine navigation antenna for highest positioning accuracy.(0 reviews)£1,160.00 Add to basket
Alpine PDXM12 Mono Bass Amp
Alpine PDXM12 Mono Bass Amp –Mono Power Density Digital Amplifier – PDX-M12
Alpine PDXM12 Mono Bass Amp – Mono Power Density Digital Amplifier – PDX-M12
Check out the new amplifier benchmark with Alpines new PDX series of amplifiers . These have been completely re-engineered to give optimal performance ,amazing sound quality & Alpine’s trusted reliabilty.
The Alpine PDX amps are a perfect compact design allowing the car audio enthusiast great potential in any audio set up.
New Reference Grade Output Stage
Ultra-Wide Frequency Response
This super-wide, industry leading frequency range offers listeners unparallel sound quality and detail that bests even the most high-end audiophile equipment. 5Hz-100kHz for 4ch, 5Hz-400Hz for Mono (+0,-3dB)
Total Harmonic Distortion Rate (THD) vs. Frequency
The all-new PDX series amplifiers are not your typical class-D amplifiers. Traditionally, class-D amplifiers have not been known for high frequency reproduction. These new PDX amplifiers are the first ever class-D amplifiers to break tradition and trump the amps of yesterday. The PDX-M12, PDX-M6, PDX-F6, and PDX-F4 are synonymous with extremely high frequency reproduction. The THD is actually falling at high frequencies, resulting in a clean and clear signal where your ear is most sensitive to distortions. -<0.005% THD+N @ 1W, <0.05% THD+N @ rated power.
Signal to Noise
These amps are capable of unheard of S/N ratio up to 95dB S/N @ 1W, 122dB S/N at rated power for extremely clean, uncolored sound. Forget unwanted background noise or static. The PDX amps deliver crystal clear music every time.
With ultra-low output impedance, the new PDX offers extremely controlled, tight bass for unprecedented sound quality. Ratings are >1000 for Mono and >500 for 4ch.
Power Output to the Extreme
Beefed up Power
The PDX power supply delivers tremendous headroom with low distortion and noise. PDX amplifiers have an extremely high total system efficiency of ~80% (power supply is rated at >90%, output stage is rated >90%).
Power Management Processor
PDX amps incorporate Alpine’s new Power Management circuit. The Power Management Processor controls all aspects of amplifier performance, monitoring voltage, temperature and output to ensure uninterrupted power output for non-stop listening. If the amp gets too hot, the Thermal Protection circuit kicks in and gradually decreases output power until it cools down. Once cool, the power output automatically increases back to the previous level. If the circuit detects a Low Battery condition, it will gradually decrease power output if battery voltage becomes too low. Once the battery voltage increases, power will be restored. This interruption-free design allows for non-stop enjoyment with no hiccups or drop-outs, just clean, clear output.
Low Impedance Stability
These amps are stable at low impedances and are capable of their rated power from 2 to 4 ohms for all models. This allows excellent flexibility with multiple speaker and subwoofer loads and is adjusted automatically.
Certified Power From Birth, Guaranteed.
Each PDX amplifier comes with its very own birth-sheet. PDX amplifiers are tested and documented to show their true actual output.
Unique Stacking System
The new PDX series amplifiers are 20% thinner than previous models at only 2″ thick. New stacking system packs the amps closer together so there are no gaps and to save space in the trunk while directly coupling the amps heatsinks to help share cooling duties.
The super high power speaker connectors allow for up to 10 mm² wiring and have a unique quick disconnect design for simple error-free installation.
The new removable connector features a low-loss, high-current design. It accepts up to 25 mm² wire, to ensure your amp gets the power it needs while allowing for easy installation.
Remote Control Bass Knob (RUX-KNOB)
Simply add the RUX-KNOB (sold separately) and get full control from inside the dash for remote on-the-fly bass adjustments. You also have the ability to control multiple amps from just one controller with simple telephone cord adapters.
A Touch of Personalization
PDX amplifiers come with easy-to-remove trim rings, so if you would like to customize them, you can have them painted. Add it as another Do-It-Yourself project, or leave it to professionals and ask an Authorized Alpine installer near you. The removable trim ring can be custom painted to match your vehicle or personalized to anything you want.
- Connectors: Quick Disconnect Terminals (Power Terminal and Speaker Terminals)
- Terminal Layout: One-Sided
- Mounting Design: Easy Stacking and Clean-look installation
- Amplifier Type: Class-D (Digital)
- Channel Design: 1 Channel (Mono)
- Thermal Protection
- Low-battery Protection
- Power Supply: Resonant Mode Power Supply
- Power Supply Design: DC-DC PWM Power Supply
- Board Circuitry: STAR Circuit
- Current Protection: Auto Over-Current Protection
- Power Indicator: Top Mounted Blue LED Power/Status Indicator
- RCA Output: Non-Fading Pre-Amp Output
- Crossover: Adjustable High Pass, Low Pass
- Pre-Amp Stage: Discrete
- Final Outputs: MOSFET
- Board Design: 6-Layer Glass Epoxy PC Board
- Gain Control: Adjustable
- Bass Control: Remote Bass Control (Sold Separately)
RMS Power Ratings
- Per channel into 4 Ohms: (@14.4V ≤1%THD+N) 1200W x 1
- Per channel into 2 Ohms: (@14.4V ≤1%THD+N) 1200W x 1
- Crossover: Variable, 50-400Hz (-24dB / oct ), (Variable, L.P.F Only 1/2 ch)
- Subsonic Filter: OFF / 15Hz / 30Hz
- Heat Sink (WxHxD) mm: 257mm x 192mm x 50.8mm
(0 reviews)£549.00 Add to basket
- Power Requirements: 14.4V DC (11V to 16V)
- Input Sensitivity: Select Vol, 0.1V to 1.0V or 1.0V to 8.0V (For Rated Power)
- Cable size: 25 mm² (BATT and GND), 4 mm² (Remote), Up to 10 mm² (Speaker)
- Frequency Response: 5 Hz – 400 kHz / 0dB ~ -3dB (Reference: 1 W into 4 Ω)
- Speaker Impedance: 4 or 1 Ω
- Signal to Noise: CEA 2006 S/N Ratio (IHF A Weighted, Reference: 1W into 4Ω) 92 dBA